Roll over image to zoom
SKU: 93637609
Grundfos Hydro MPC-E 2 x CRIE 20-1 Three Phase 2 x 2.2kW 304ss Booster System w/8L Tank and CU 352 Controller
Australia-Wide
(08) 9240 2992
Official Grundfos
Peace of Mind
Product Overview
For expanding commercial sites whose original mains feed no longer keep pace, a factory-assembled Hydro MPC-E 2 CRIE 20-1 package provides a well-matched solution, with two CRIE 20-1 pumps staged against the demand curve. Specify part number 93637609 and the whole set lands tested, assembled and ready for pipework.
Flow capacity reaches 1160 L/min. Up to 20 metres of head is available to maintain pressure as demand changes. Control sits with the GENIECON multi-pump controller in its touch-equipped panel, adjusting each pump individually and rotating duty by load, run hours and faults.
The two-pump package arrives as one base-mounted assembly with stainless steel manifolds, two 80 mm manifold connections, valves, sensors and a pressure gauge, plus an 8L diaphragm tank. Electrical supply is 3 x 400 V at 50 Hz with a rated current of 8.9 A. The motors have IP54 protection and the system is rated to 16 bar maximum pressure. Liquid-temperature suitability is 5°C to 60°C.
Its home ground covers irrigation schemes, commercial buildings and water supply networks. The variable-speed system suits clean-water boosting duties with changing demand.
Features
- The controller tracks the pressure setpoint with proportional deviation alerts before conditions become faults.
- Each pump is driven by permanent magnet motors with frequency-controlled speed matching demand.
- Pump staging follows demand automatically: pumps enter at low speed as pressure drops, ramp to equal speed, and exit as flow fades.
- Two Grundfos CRIE 20-1 vertical multistage pumps run in parallel on one common base frame.
- Rated for 16 bar system pressure; motors carry IP54 protection.
- The GENIECON UNIT applies the pumps' exact hydraulic and electrical data when making control decisions.
- The touch-panel GENIECON interface shows system status and allows direct setpoint changes on the door.
- Inlet pressure monitoring provides dry-running protection if the suction supply is insufficient.
- Energy draw matches the actual job because speed follows demand, not a fixed curve.
- Stainless steel manifolds provide two 80 mm manifold connections ready for pipework.
- An integrated 8L diaphragm tank carries small draw-offs and limits pump cycling.
- Rated 2.2 kW (P2) on every main pump in the frame.
- The package is wet-tested and pre-configured, requiring only pipework and power on site.
What's Included
- 2 x Grundfos CRIE 20-1 vertical multistage pumps
- IE5 permanent magnet motors with integrated frequency converters
- GENIECON PANEL with touch display
- GENIECON multi-pump control unit
- Stainless steel suction manifold
- Stainless steel discharge manifold
- Non-return valves
- Isolation valves
- Pressure sensors/transmitters
- Pressure gauge
- Inlet pressure monitoring (dry-run protection)
- 8L diaphragm pressure tank
- Factory assembled and tested booster system
SPECIFICATIONS
| Max Flow | 1160 L/Min |
| Max Head | 20 m |
| Power | 2 x 2.2 kW / 415v |
| Rated Current | 8.9 Amps |
| Suitable For | Commercial Water Supply, Irrigation and Transfer Duty |
| Body Material | Stainless Steel |
| Liquid Temperature | 5°C – 60°C |
| Inlet Size | 80 mm |
| Outlet Size | 80 mm |
| Warranty | 24 Months |
Warranty & Returns
All products supplied by Foundation Pumps are covered by a minimum 12-month warranty unless otherwise stated. Some brands may offer longer manufacturer warranties. Warranty covers manufacturing defects, faulty materials and workmanship under normal use.
- Products must be installed correctly and in accordance with the manufacturer’s instructions.
- Warranty does not cover incorrect installation, misuse, dry running, normal wear and tear, unauthorised repairs or damage caused by external factors.
- Proof of purchase, photos, videos and installation details may be requested when assessing a warranty claim.
- The customer is responsible for returning the product to Foundation Pumps or the nominated service centre unless otherwise agreed.
- Removal, reinstallation, labour and associated site costs are generally the customer’s responsibility unless required under Australian Consumer Law.
- Change-of-mind returns may be accepted within 30 days provided the product is unused, uninstalled and returned in its original packaging.
- Customers are responsible for return freight costs for change-of-mind returns.
- Restocking fees may apply to special-order, bulky or non-stocked products.
- Used, installed or specially ordered products may not be eligible for change-of-mind returns.
- If a product arrives damaged or faulty, please contact Foundation Pumps as soon as possible so we can assist with the appropriate repair, replacement or refund.
Your rights under Australian Consumer Law are not affected.
Under high elevation demands, what total dynamic head does this parallel booster set produce?
Under peak line requirements, the Grundfos Hydro MPC-E 2 CRIE 20-1 V1 GA-A-A-AG delivers a maximum vertical head of 20 m and accommodates working system pressures up to 16 bar.
What manifold sizing and valve hardware connects the parallel pump wet ends on this set?
Factory pipework configuration on the Hydro MPC-E 2 CRIE 20-1 incorporates DN80 stainless steel manifolds, complete with individual pump isolating valves and line non-return valves.
What manufacturer warranty protection covers this Grundfos booster assembly?
Factory backing for the Hydro-MPC-E-2-CRIE-20-1 includes an authentic Grundfos two-year manufacturer warranty covering the pumps, drive electronics, and skid assembly.
Which water delivery capacity does this packaged multi pump unit provide under full operational demand?
At full operational capacity, the Hydro MPC E 2 CRIE 20 1 provides up to 1160 L/min total water throughput to satisfy heavy facility consumption requirements.
How does the integrated variable frequency drive regulate motor speed across changing flow rates?
Power for the 2 CRIE 20-1 (Hydro MPC-E) is delivered via two high-efficiency variable frequency drive MGE electric motors of 2.2 kW each, wired for a 3 x 400 V electrical supply with built-in speed regulation.
Need help choosing the right pump?
Our team of pump experts are here to help you find the perfect solution for your application.
- Free expert advice
- Pump sizing & system recommendations
- Fast response — call or email us