Roll over image to zoom
SKU: 93637840
Grundfos Hydro MPC-E 2 x CRNE 10-6 Three Phase 2 x 4kW 304ss Booster System w/8L Tank and CU 352 Controller
Australia-Wide
(08) 9240 2992
Official Grundfos
Peace of Mind
Product Overview
For residential towers and medium commercial sites outgrowing their mains pressure, a factory-assembled Hydro MPC-E 2 CRNE 10-6 package provides a well-matched solution, with two CRNE 10-6 pumps staged against the demand curve. One factory-tested package replaces a shelf of loose components; order part number 93637840 to put it on site.
This set provides up to 520 L/min of flow capacity. Variable-speed operation can develop up to 87 metres of head where required. A Grundfos GENIECON PANEL on the common base frame provides the system control; the GENIECON UNIT within it holds the exact hydraulic and electrical data of the pumps, so staging and changeover decisions are based on the pumps' actual curves.
Factory assembled on a common base, the set combines stainless steel pipework, two 50 mm manifold connections, isolation and non-return valves, pressure sensors and a gauge, plus an 8L diaphragm tank. It connects to a 3 x 400 V supply at 50 Hz with a rated current of 15.5 A. Motors are protected to IP54, while maximum system pressure is 16 bar. Liquid-temperature suitability is 5°C to 60°C.
Expect it on water supply networks and irrigation schemes sites, plus high-rise developments duties. It provides clean-water pressure boosting for both new plant rooms and refits.
Features
- Maximum operating pressure of 16 bar with motors sealed to IP54.
- A suction-side pressure sensor guards the pumps against dry running.
- Two Grundfos CRNE 10-6 pumps share the boosting work in parallel.
- Stainless steel manifolds provide two 50 mm manifold connections ready for pipework.
- Constant pressure control holds the delivered pressure flat while proportional mode lets setpoints flex with demand.
- An integrated 8L diaphragm tank carries small draw-offs and limits pump cycling.
- Energy draw matches the actual job because speed follows demand, not a fixed curve.
- Rated 4 kW (P2) on every main pump in the frame.
- Control decisions come from real pump curves, not generic models, via the GENIECON UNIT.
- Each pump is driven by permanent magnet motors with frequency-controlled speed matching demand.
- Factory assembled and wet-tested, the set arrives pre-configured for straightforward installation.
- The touch-panel GENIECON interface shows system status and allows direct setpoint changes on the door.
- Pumps are cut in and out according to demand, every running unit turning at the same speed to hold the pressure set point.
What's Included
- 2 x Grundfos CRNE 10-6 vertical multistage pumps
- IE5 permanent magnet motors with integrated frequency converters
- GENIECON PANEL with touch display
- GENIECON multi-pump control unit
- Stainless steel suction manifold
- Stainless steel discharge manifold
- Non-return valves
- Isolation valves
- Pressure sensors/transmitters
- Pressure gauge
- Inlet pressure monitoring (dry-run protection)
- 8L diaphragm pressure tank
- Factory assembled and tested booster system
SPECIFICATIONS
| Max Flow | 520 L/Min |
| Max Head | 87 m |
| Power | 2 x 4 kW / 415v |
| Rated Current | 15.5 Amps |
| Suitable For | Commercial Water Supply, Corrosive Transfer Duty |
| Body Material | Stainless Steel |
| Liquid Temperature | 5°C – 60°C |
| Inlet Size | 65 mm |
| Outlet Size | 65 mm |
| Warranty | 24 Months |
Warranty & Returns
All products supplied by Foundation Pumps are covered by a minimum 12-month warranty unless otherwise stated. Some brands may offer longer manufacturer warranties. Warranty covers manufacturing defects, faulty materials and workmanship under normal use.
- Products must be installed correctly and in accordance with the manufacturer’s instructions.
- Warranty does not cover incorrect installation, misuse, dry running, normal wear and tear, unauthorised repairs or damage caused by external factors.
- Proof of purchase, photos, videos and installation details may be requested when assessing a warranty claim.
- The customer is responsible for returning the product to Foundation Pumps or the nominated service centre unless otherwise agreed.
- Removal, reinstallation, labour and associated site costs are generally the customer’s responsibility unless required under Australian Consumer Law.
- Change-of-mind returns may be accepted within 30 days provided the product is unused, uninstalled and returned in its original packaging.
- Customers are responsible for return freight costs for change-of-mind returns.
- Restocking fees may apply to special-order, bulky or non-stocked products.
- Used, installed or specially ordered products may not be eligible for change-of-mind returns.
- If a product arrives damaged or faulty, please contact Foundation Pumps as soon as possible so we can assist with the appropriate repair, replacement or refund.
Your rights under Australian Consumer Law are not affected.
Which pipe connection fittings and check valves are assembled onto this packaged booster skid?
Header plumbing on the Grundfos Hydro MPC-E 2 CRNE 10-6 V1 GA-A-A-AG provides R 2 1/2" stainless steel suction and discharge connections accompanied by isolating valves and discharge check valves.
Under what factory warranty coverage is this multi pump booster skid supplied?
Protection on the Hydro MPC-E 2 CRNE 10-6 is provided by a comprehensive Grundfos two-year manufacturer warranty with extensive Australian technical service and spare parts support.
What volumetric water flow does this packaged booster assembly supply for high demand installations?
Under maximum network draw, the Hydro-MPC-E-2-CRNE-10-6 supplies a peak fluid flow rate of up to 520 L/min across its variable speed centrifugal stages.
What motor drive hardware powers and modulates the centrifugal pumps on this booster package?
Propulsion across the Hydro MPC E 2 CRNE 10 6 is supplied by two variable frequency drive MGE electric motors rated at 4 kW each, operating on a 3 x 400 V electrical supply with integrated frequency converters for precise pressure control.
What vertical pumping head and maximum system pressure rating applies to this booster package?
For vertical pressure boosting, the 2 CRNE 10-6 (Hydro MPC-E) produces up to 87 m total elevation head with a 16 bar maximum working pressure envelope.
Need help choosing the right pump?
Our team of pump experts are here to help you find the perfect solution for your application.
- Free expert advice
- Pump sizing & system recommendations
- Fast response — call or email us