Roll over image to zoom
SKU: 93637559
Grundfos Hydro MPC-E 3 x CRIE 10-3 Three Phase 3 x 2.2kW 304ss Booster System w/8L Tank and CU 352 Controller
Australia-Wide
(08) 9240 2992
Official Grundfos
Peace of Mind
Product Overview
For gymnasiums, aquatic centres and student housing running wall-to-wall showers, a factory-assembled Hydro MPC-E 3 CRIE 10-3 package provides a well-matched solution, with three CRIE 10-3 pumps staged against the demand curve. Quote part number 93637559 to have it arrive pre-configured and ready for the plant room.
The system supports flow rates up to 781 L/min. It can develop up to 43 metres of head for dependable pressure boosting. Control sits with the GENIECON multi-pump controller in its touch-equipped panel, adjusting each pump individually and rotating duty by load, run hours and faults.
Factory assembled on a common base, the set combines stainless steel pipework, two 80 mm manifold connections, isolation and non-return valves, pressure sensors and a gauge, plus an 8L diaphragm tank. It connects to a 3 x 400 V supply at 50 Hz with a rated current of 12.9 A. Motors are protected to IP54, while maximum system pressure is 16 bar. Liquid-temperature suitability is 5°C to 60°C.
Expect it on commercial buildings and irrigation schemes sites, plus water supply networks duties. It provides clean-water pressure boosting for both new plant rooms and refits.
Features
- Both constant-pressure and proportional-pressure modes are available, so plant rooms can tune response to pipework.
- Pumps are cut in and out according to demand, every running unit turning at the same speed to hold the pressure set point.
- An integrated 8L diaphragm tank carries small draw-offs and limits pump cycling.
- Variable speed comes from frequency converters matched to permanent magnet motors, keeping the booster set in its efficient range.
- The stainless steel manifold assembly is supplied with two 80 mm manifold connections.
- At P2 each main pump is 2.2 kW, covering the duty without oversizing the frame.
- Inlet pressure monitoring provides dry-running protection if the suction supply is insufficient.
- Slow-speed duty and staged switching keep consumption down through low-demand hours.
- The GENIECON UNIT applies the pumps' exact hydraulic and electrical data when making control decisions.
- The touch-panel GENIECON interface shows system status and allows direct setpoint changes on the door.
- Maximum operating pressure of 16 bar with motors sealed to IP54.
- Three Grundfos CRIE 10-3 pumps share the boosting work in parallel.
- Factory assembled and wet-tested, the set arrives pre-configured for straightforward installation.
What's Included
- 3 x Grundfos CRIE 10-3 vertical multistage pumps
- IE5 permanent magnet motors with integrated frequency converters
- GENIECON PANEL with touch display
- GENIECON multi-pump control unit
- Stainless steel suction manifold
- Stainless steel discharge manifold
- Non-return valves
- Isolation valves
- Pressure sensors/transmitters
- Pressure gauge
- Inlet pressure monitoring (dry-run protection)
- 8L diaphragm pressure tank
- Factory assembled and tested booster system
SPECIFICATIONS
| Max Flow | 781 L/Min |
| Max Head | 43 m |
| Power | 3 x 2.2 kW / 415v |
| Rated Current | 12.9 Amps |
| Suitable For | Commercial Water Supply, Irrigation and Transfer Duty |
| Body Material | Stainless Steel |
| Liquid Temperature | 5°C – 60°C |
| Inlet Size | 80 mm |
| Outlet Size | 80 mm |
| Warranty | 24 Months |
Warranty & Returns
All products supplied by Foundation Pumps are covered by a minimum 12-month warranty unless otherwise stated. Some brands may offer longer manufacturer warranties. Warranty covers manufacturing defects, faulty materials and workmanship under normal use.
- Products must be installed correctly and in accordance with the manufacturer’s instructions.
- Warranty does not cover incorrect installation, misuse, dry running, normal wear and tear, unauthorised repairs or damage caused by external factors.
- Proof of purchase, photos, videos and installation details may be requested when assessing a warranty claim.
- The customer is responsible for returning the product to Foundation Pumps or the nominated service centre unless otherwise agreed.
- Removal, reinstallation, labour and associated site costs are generally the customer’s responsibility unless required under Australian Consumer Law.
- Change-of-mind returns may be accepted within 30 days provided the product is unused, uninstalled and returned in its original packaging.
- Customers are responsible for return freight costs for change-of-mind returns.
- Restocking fees may apply to special-order, bulky or non-stocked products.
- Used, installed or specially ordered products may not be eligible for change-of-mind returns.
- If a product arrives damaged or faulty, please contact Foundation Pumps as soon as possible so we can assist with the appropriate repair, replacement or refund.
Your rights under Australian Consumer Law are not affected.
What fluid displacement flow rate does this multi pump booster assembly provide under full duty?
Operating across its factory curve, the Grundfos Hydro MPC-E 3 CRIE 10-3 V1 GA-A-A-AG discharges up to 781 L/min of clean water to maintain consistent line pressure during peak demand cycles.
How are the pump wet ends powered and electronically modulated across variable facility draw?
Each centrifugal stage of the Hydro MPC-E 3 CRIE 10-3 is driven by a 2.2 kW variable frequency drive MGE electric motor running on 3 x 400 V power, utilizing built-in variable speed drives to adjust output dynamically.
Which total head pressure does the multi pump package maintain across the distribution network?
Elevating water across multi-level pipework, the Hydro-MPC-E-3-CRIE-10-3 maintains up to 43 m total dynamic head with an overall 16 bar maximum operating limit.
Which pipe connection sizes and manifold isolation valves are fitted across this booster package?
Plumbed for rapid site installation, the Hydro MPC E 3 CRIE 10 3 includes DN80 stainless steel headers equipped with dedicated isolating valves, check valves, and pressure transmitters.
How is this packaged booster assembly backed by manufacturer warranty coverage?
Grundfos provides two-year manufacturer warranty coverage on the 3 CRIE 10-3 (Hydro MPC-E), securing the complete multi-pump package, manifolds, and integrated electronics.
Need help choosing the right pump?
Our team of pump experts are here to help you find the perfect solution for your application.
- Free expert advice
- Pump sizing & system recommendations
- Fast response — call or email us